I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...
Hi,
Everyone,
I am using NRF51422 chip for my custom board. with transmission interval set to 2000ms and Tx power to -20 dBm, I transmit 32 Bytes BLE data and Scan and...
I use the softdevice which is s130.The code is from the demo:
static void nus_data_handler(ble_nus_t * p_nus, uint8_t * p_data, uint16_t length)
{
for (uint32_t i =...
Hi,
i'm using SPI to transfer data divided into packets of 24 bit from NRF51 to a DAC. The function that allows to send data is:
spi_master_send_recv(SPI_MASTER_1, data_vector_tx...
I'm having trouble starting my application after power cycling after flashing it with the DFU app.
I started nRFgo Studio. Erased the chip. Programmed the SoftDevice (s130_nrf51_2...
I was just wondering if anyone has any experience with or thoughs about using Zephyr ( www.zephyrproject.org/) or Mynewt ( http://mynewt.apache.org/) that they would like...
Hello all,
i am struggling with the example code of the Enhanced ShockBurst Protocoll in SDK 11. I cannot really see the structure of the code, to which time which event...
Hi all, in the forum I can read about people having issues with wrong CRC in the bootloader, but with SDK11; I have the opposite problem. It is always 0 and is always accepted...
main.c Hi,
I am having an issue with I2C transaction in my program.
There are two sensors(Touch and Temp) connected to the I2C bus. Touch sensor is working well when...
According to the official tutorial must before the MCU is powered on hold button 4 to enter DFU mode, detected that I how to achieve a certain GPIO port high level into DFU...
Hi,
I am designing a system that will include an nRF905 transceiver. How accurate should the nRF905 oscillator frequency be for each receiver/transmitter in order to ensure...
