I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I'm updating our bluetooth firmware and boot loader over the air from iOS and android devices. I've modified the nordic supplied update code (IOS-nRF-Toolbox project) to support...
I would like to use functions from components/libraries/mem_manager/mem_manager.c but it doesn't compile because of absense of sdk_config.h header file.
/home/gerbsh/sdk_11...
I'm concentrating on a work about connecting nrf51-dk device in the sensor node end implementing COAP server, ble enabled rapsberrypi and COAP client using Copper.
To check...
The PPI has been configured to transmit a message every time the timer triggers ( every 1ms).
I'm using IAR Embedded Workbench 7.40.3.8938 as my IDE .
When the system...
Hello all,
Our product based on nRF51 is on preproduction stage. We use both 16MHz and 32kHz external crystals.
The question is:
Is there any way to check programatically...
Dear all,
I do have troubles with the bandwidth of the nRF51822 contained in the Adafruit's Bluefruit LE SPI Friend module. The max. throughput I get is 213 B/s. I'm using...
After doing some DFU work - and it all went fine and dandy ...
I would like to go back to the plain old default bootloader that came with my nRF51 board. I don't seen any...
I'm using IAR IDE for the nordic development of NRF51822 (mdbt40). I'm able to run the example project which does not required soft device. Now i wanted to move further with...
Hi,
Is it possible to program the nRF51-Dongle through the usb, to correspond to Bluetooth content to change GPIO state. Then connect the dongle to an external power source...
Greeting , Nordic team , i have some questions about my project.
First , my hardware and software is following:
nrf51422 (pca10028)
SDK 9.0
SoftDevice S110
My project...
Hi,
I am looking for the possibility of getting an unforgeable unique ID of a bonded device within a BLE connection.
Using nRF51422 with SD310 for the peripheral, any...
Hi, could anyone please help me as I currently using nrf51822-arduino-library in a nrf51822 chip and I couldn't call the interrupt function : wakeUp(). Current I'm connect...
hello,
I want to connect Arduino shield with heart-rate sensor to my nRF 51 DK board.
then i have to receive sensor data continually from the sensor.
my plan is transferring...
Hello there,
I'm currently using nrf52832 with s132 and sdk 0.9.2, based on the 'ble_app_uart' example and keil5. I'm concerned about the current consumption because in...
I am working on nrf52 DK board with eclipse gcc + nRF52 SDK 0.9.2. I found the experimental nfc project but it does not include the gcc make file. I would like to ask:
...
