Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody!
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
Hi Nordic team,
This is a compatibility test. case1 okay: 1,Connect the nRF5340BIS headset with the phone. 2,NRF5340 broadcast can be found on the mobile phone. 3,When you...
Hello Nordic Team! I'm experiencing unusual issues with GPIO pins on an nRF54L15 custom board. Specifically, P0.02 and P1.03 are not behaving as expected. Button Issues (P0...
Hi,
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
I've seen a few posts about this, but they are all old, and maybe don't apply to USB-C We have a device that already uses USB-C for battery charging. We want to carry the...
Hello I have a custom board with the following dts My zephyr app crashes in bt_enable() Note that uart0 TX pin 8 is used by gps_vrtc_en but uart0 is not defined. Same crash...
Hi
I have been using my out of tree driver for my BG95 module, which I have copy pasted from the zephyr's quectel_bg9x driver (drivers/modem/quectel-bg9x) and its required...
Today I opened VS Code to find all my Zephyr/NRF #includes have the red squiggly lines with an error such as "cannot open source file zephyr/types.h". Right click -> Go to...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
I found this in nRF5_SDK_17.0.2_d674dde/components/libraries/memobj/nrf_memobj.h :
/ ** * A memory object can consist of multiple chunks with the same size. Each object...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...