I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
8.0, multilink example, peripheral, s110 softdevice.
By walking through sections of codes and doing some research, I reckon if a connection were being established after...
I try to Development with GCC and Eclipse following tutorial
but i get some problem , which i can not solve alone.
so hopelly someone can help me to solve it ,thx!
that...
Hi，I use nRFgo Studio to erase nRF51822, like this
but it display: ERROR: Invalid serial number!
I found the question how to use nrfjprog --snr??? ，I can get the...
I am using the nrf24l01 on a FRDM k64f board, I want to communicate between the board and my laptop, so I have bought a nrf51 dongle.
I am using mbed on the k64f board...
I try to create a custom boot loader that enable to update soft device via data come in from SPI msg. When I try to use the command nrf_nvmc_page_erase() to erase the flash...
Hi everyone,
I'm a beginner in Android development and BLE environment, and I want to communicate with the nRF52 card using an Android app. In fact I have to develop an...
hi,
I am using the nRF51 with code from SDK 9, as well as the S110 softdevice and made a custom service(128-UUID) with bond using device manager.
connection and service...
Hi,everyone,
I would like to know that what's the dedicated bonding ?
I saw this in the introduction of a BT chip.
I am confused with 'dedicated bonding'.
And what's...
Hi,
I am using the nRF52 with code from SDK 9.2, as well as the S132 softdevice. I basically ported code from the ble_uart_app into the twi_example to send data over bluetooth...
In the very first blinky example from the nRF52_SDK_0.9.1:
#include "stdint.h"
#include "stdint.h"
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards...
hello,my experiment phenomenon is:one nRF24L01's channel is 0x0A,used as send terminal；the other one nRF24L01's channel is 0x02，used as receive terminal；receive terminal can...
I try to make a build of the example ble_app_hrs_rscs_replay_pca10028 (central and peripheral experimental) in SDK 10. My MCU is nRF51822-CFAC, and I'm using IAR compiler...
I'm using custom board with 32MHz oscillator and S110 SD 7.1 (SDK 6.1).
Somteimes (quite rare) the chip completely hangs when calling sd_flash_erase in pstorage.c.
Only...
hello
we use nRF51822 QF AC A1 / IC rev 3 with SDK 6.1.0 / S110 7.1.0. We have produced and delivered to client > 1k units
pwm code nrf_pwm_noglitch 02.2015 from
github...
