Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
my dk board is nrf51422 and nrf 52382,
the central role is nrf51422, and the peripheral role is 52382.
my sdk version of 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I'm trying to get a module with an NFR24L01+ on board to send a simple data transmission from a pic micro but after a couple of days of trying various combinations without...
i find that the macro APP_ERROR_CHECK call the macro APP_ERROR_HANDLER
do \
{ \
const uint32_t LOCAL_ERR_CODE = (ERR_CODE); \
if (LOCAL_ERR_CODE != NRF_SUCCESS) \...
HI all:
Because the application code is relatively small, bootloader is used dual_bank_mode, but now the application code becomes large, OTA can not upgrade, I would like...
My PCA10001 board is getting detected in nRFgo studio and i can even program it but its COM port is not getting detected in device manager.
I dont know what happened but...
Hello Nordic--
We're most of the way through qualification testing on an nrf51822 and the testing house had a question about the PIXIT values for RF-PHY testing. I sent...
Hi,
I find three different states that is related to DFU and app_button libary.
1, no DFU(that is no bootloader), but using app_button libary, there is no 0.9mA current...
Hi. I use the 'sdk 6' and 's110_nrf51822_7.1.0_softdevice'.
I would like to add security.
I tried to passkey. If i enter passkey, it is possible to bond. but It is not...
Hi all,
I can control volume up/down, music play/pause with the ble_hids module.
static uint8_t report_map_data[] =
{
0x05, 0x0c, // Usage Page (consumer device)
0x09...
Hi.
I'm currently trying to buffer data from beacon interrupt.
So, I choose to use circular buffer.
Before implementing it myself, I could find that there's already...
Hi
I'm using the Adafruit LE Breakout with an MSP430.
I made my own drivers in order to have full ISR support.
My setup works well (no error) i can connect/set_local_data...
Hi,
I’m currently trying to send strings about Nordic UART Service.
In use are two nRF52832 Develop boards. One as Central and one as Peripheral.
The connection works fine...
I have a PCA10040.
I downloaded nRF52_SDK_0.9.2_dbc28c9.zip.
I want to use "ble_peripheral\ble_app_uart " sample program.
However, supporting it is PCA10036. (by readme...
I am modifying the ble_central\ble_app_hrs_c example to connect to a peripheral with an "Authentication Characteristic" that is used to initiate the peripheral-specific authentication...
