I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
I want to measure a current consumption for the 3rd-party evaluation board which has 32MHz crystal and 32KHz crystal, and there is not PO.18 on the 3rd-party evaluation board...
Hi,
I use nRF51822.
Is it possible to change a beacon timing of the advertiser by a trigger of the acceleration sensor in the advertising mode?
Thank you for any...
Hello everyone,
I compiled the nrf51-app-button-examples without any error and warnings but it is showing me this error (No cortex -M Device found in JTAG chain / Target...
According to PCA10028_Schematic_and_PCB.pdf (Rev 1.2.0), page 7, there should be SB22-25 surrounding TP5-8:
On my PCA10028, I have TP5-8, but no SB's there:
What...
Hi All,
I'm having a problem with my application which involves regularly sampling I2C slave data and sending it over Bluetooth. The I2C slave generates an active high...
It looks like the RTC0_CONFIG_FREQUENCY define in nrf_drv_config.h which is located in nearly every project may have a typo. The define is listed as 32678, and the RTC1 define...
I am seeing a problem identical to what's described in this question . I'm using SDK version 10.
My timers work fine for a while, but then suddenly and seemingly at random...
Hello, I am trying to build Smart beacon kit firmware from sources.
From ble_app_beacon folder I have built the firmware using armgcc (with the proper makefile) and got hex...
Hello,
The documentation states, that "maximum consecutive TX time is limited"
17.1.9 Maximum consecutive transmission time Maximum
consecutive transmission time...
Hi,
I have a JLink script which sets APPROTECT in the UICR to enable readback protection and disable the debug interface.
For development purposes, I would like to be...
Hi,
I tried to use nrf51822 to update light intensity of 64 area to smartphone and then the smart phone will display those light intensity values in gray scale. I want...
Hi everyone!
During the development of our device, we faced with some problems:
So now we need to read the data array in a clear sequence from characteristics. The data...
Hi,
I have a device running firmware from SDK10 and using s110. I would like to update the device to use SDK11 firmware with S130v2. I'm using following code to generate...
Hello,
my application hex used to work fine before i change my bootloader and softdevice
now after falshing all the hex including the application , it is advertising as...
Hi,
I want data read from my sensor (gives continuous data when button is being pressed). and then send it through Bluetooth equipment.(PC or iPhone and so on) But i don...
