Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Im getting the following error ,when I try to compile the example ble_HID_template from the latest Arduino Nordic Release:
ble_HID_template.ino: In function 'void aci_loop...
-- When a ble peripheral starts advertising and then receives a BLE_GAP_EVT_CONNECTED event, the stack stops advertising automatically right?
-- When you get BLE_GAP_EVT_CONNECTED...
Hi
I have successfully created services and characteristic from nRFGO Studio and they are advertising well even receiving and transmitting is going well. Now my problem...
Hello,
i ported example of mouse by HID for nRF51822 to nRF51422. The device is detected as mouse by Bluetooth in Windows 7 but I cannot to connect it. Any ideas whats wrong...
Hi,
I'm wanting to develop some solutions around the NRF518222 IC. I want to try out the various modes etc, bluetooth and ANT as well as trying to get some longer range...
I try the throughput in S310,
I refer the "nrf51-ble-app-lbs" to make our code(interval is 20ms),
and test with Master Control Panel.
it seen only have 1.7KBps.
Could...
Hi,
I am trying to detect if a disconnection occurs due to a signal loss.
In the application's BLE Stack event handler, I have found that there is a disconnect reason...
I'm new to BB 10 development using native NDk provided by Blackberry (Momentics IDE)
Developing app with Bluetooth LE device, But having problem to discover the BLE device...
Recently I open the sdk of the nrf51422,there are some functions that indicate that they are come from the document call 'ant_interface.h'.But when I try to go to the definition...
I'm ending up in the HardFault_Handler() on calling sd_app_evt_wait() within a function that reads from the UART. What might cause that? Stack screenshot attached.
I have...
I'm using nRF51822 for development. and I want to use ADC to measure the electricity of battery, but I don't know the discharge characteristic, i couldn't get that on internet...
#define IO_CHERRY8x16_ROW_PORT 0x13E02040UL
#define IO_CHERRY8x16_COLUMN_PORT 0x60031FBFUL
Why this number be defined like this ? What are this two things use for?
...
Hi,
I'm trying to compile the bootloader example using GCC instead of Keil compiler.
To do so, I copied the bootloader example and started editing the file bootloader_util_arm...
Hi, I am working on my new project. My goal is a sensor network. I have to create four service, one or two basic service like htm and battery service and other with contains...
