Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi Sir
The npm1300 allows setting the default voltage using resistor values as shown in the table below. However, if I want to set the voltage to 1.05 V using resistors...
I am working on synchronizing RTC timers on several nrf52832s and i would like to have a single clock clocking all the RTCs on all the boards. I understand that the LFCLK...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
We're developing a low-power application on the nRF9160 where we need the device to stay connected to the server over LTE, so we cannot enter System OFF mode. Instead, we...
Hello,
I am developing a product using the nRF54L15 and have noticed a discrepancy in the documentation regarding clock pins. My intention is to use pins 1.02 (SDA) & 1...
Describe Need to repeat disconnect/connect cycle after BT timeout. Problem is when using UART over BT with Nus Shell when connection is terminated by timeout (for example...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi, It's looks like I bricked my Thingy:91x . It was working fine when I program it with the target " thingy91x/nrf9151/ns " then later while learning I try program the in...
Hello,
I've got some questions regarding the use of DFU target library. I get my update data from the UART and like to use a setup with two partitions on my device. Is this...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
