Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. We are using Laird BL5340 and SDK2.8.0 for our product.
The audio waveform during a wireless...
first i change to my kconfig file add this
source "samples/subsys/usb/common/Kconfig.sample_usbd"
source "Kconfig.zephyr
second I add to cmakelits
include...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello Nordic Team,
I am currently working on a Class 3 medical device that requires time-critical communication . I am exploring options for integrating Classic Bluetooth...
A few years back I used a multilink project developed by one of the Nordic support personnel, to allow using the nRF52840 devkit board to talk to one of several Peripherals...
Hey there! I'm just a beginner and was working on a simple UART project in Segger Embedded Studio. The codes were working fine until I started encountering multiple errors...
Dear Nordic,
I am currently conducting a task where one initiator performs Channel Sounding sequentially with three reflectors.
My approach is as follows: First, I...
In my project (SDK 2.9.1), I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hi,
I'm using SDK5 17.1.0 and SD132 v7.3.0. At the moment I'm developing a central device which scans for a peripheral. I did this a few times before with other devices...
I am using seed XIAO for one of my projects having nrf 52840 ic so in order use the nrf chip on my custom pcb i have to bootload the nrf 52840 IC purchased from digikey. I...
