Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello
I am using gazell on the nRF24LE1.
I would like to know some recommendations on how to estimate a consumption on the side of the device based on the times and repetitions...
Hi. I just recently started using nRF24L01+. I am trying to simulate MultiCeiver using 2 mcus and 2 nrfs.
PTX sends a message on all 6 pipes of the PRX. The problems start...
HI,
I look at nRF5 SDK doc about Gazell,see that 'the nrf_gzll_device_tx_info_t contains the num_channel_switches parameter which can be used by application to determine...
Hello
I am quite a beginner and have been trying to get it work for 2 weeks now.
I would like to merge these 2 example codes from nordic:
Shockburst TX example...
Hi everyone,
I want to use MasterEmulator.dll (2.1.13.14) in my own application (C#) for development. Then I realised that line
MasterEmulator mMasterEmulator = new...
I am using nRF52 and Raspberry Pi 3 (with BLE).
In the Raspberry Pi, I am using bluez.
I was attempting to connect with the NORDIC_BLINKY app but the message below was...
Hi, I wonder how to get the Nordic SDK-examples work with VisualGDB.
As I would like to read TWI sensor values a good point to start from are the Nordic examples.
But...
my project is used nrf51822 mcu, it contains SIM, when the mcu is reading SIM data, and at the same, I take out theSIM, and the 51822's pin which is link with SIM is can't...
Hi, Nordic
I use SDK12.1 with nRF52832, I found one issue:
if I do not program bootloader, nRFgo Studio can program app.
First, erase all flash, then program softdevice...
Hi Everone/Nodiac
I had tried so many threads and previous questions but not bale to get my answer so asking after two weeks.
I am willing to send a string from stm32f4...
Hello,
I currently working with the nRF52832 chip on a custom board. The external clock is a 32MHz clock with +/- 10 ppm. When I use nrf_delay_us or nrf_delay_ms the delay...
Hi all,
I am using a C# application with the masteremulator dll to connect to a nRF51822 with S110 V8.0.0
I can bond with a new device, and communicate with it in a...
In developing the device, for very low battery consumption, I encountered a feature of the implementation Gazell (ESB) protocol.
When I send a packet from the DEVICE (PTX...
