I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
I'm using an nRF52832 with the S132v2 and SDK 11 and wanted to test the ble throughput.
The nRF52832 should send as many as it can to an "normal" BLE-USB-Stick.
...
In SDK 11 the FreeRTOS port has the following line is declared in portmacro_cmsis.h
#define portNRF_RTC_PRESCALER ( (uint32_t) (ROUNDED_DIV(configSYSTICK_CLOCK_HZ, configTICK_RATE_HZ...
After updating from sdk11 to sdk12, the application only starts in debug. If started with reset, it hangs. I am running on a pca10028 board an with EmBlitz 1.0. NRF51 is QFACA1...
When I test the example, When I disconnect my phone of the nordic board.
I can use the other Phone to connect the nordic board
So, I think that how to avoid the connect...
I compile blinky_pca10040
I use IAR EWARM - ARM Cortex compiler
I have a Rigado BMD-300 on my PCB
Use J-LINK EDU
When I try to download and debug, I get the error
"Failed...
Hi
I came across this article:
www.nordicsemi.com/.../Bluetooth-Smart-hearing-aid-receives-stereo-audio-direct-from-iOS-devices-and-can-recognize-and-optimize-settings...
Hi, I want to change some configurations of my beacon such as packet type, UUID, Tx power and so on, in an online manner through the Bluetooth connection(by an application...
Hi I have run into this error when running. However it has just appeared (the FDS did work but now will not initilise.) I am using Visual_gdb.
As per this issue
I have...
Hi,
I am using nRF8001 with a MCU from PIC18F family. I have successfully configured nRF8001 to send and receive data through the nordic UART pipe (I used the app nRF UART...
I am experiencing a strange problem with stopping a scan. I am using the mesh from github.com/.../nRF51-ble-bcast-mesh together with interval scanning, meaning start scanning...
Hello Nordic developers,
I was tracing through the new SD init code in the HRS example app for nRF52 and followed this macro into softdevice_handler.h. Is it supposed to...
I am planning on using:
NRGF51822 CDAB WCSP (= 128KB Flash, 16KB RAM, 3.5x3.5mm)
Another main chip I will be using is:
LSM303AGR ( www.st.com/.../en.DM00177685.pdf)
...
