we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hello,
I would like to return a specific error when a device connects to my NRF52 (by bluetooth) when for example the range of mac address is wrong to me... (or something...
Dear Folks,
I have a question regarding the supply rise time of the nRF52-Series.
According to the Product Specification Chapter 6 Table 8 the Supply rise time (0 V...
Hi, I encountered some problem using the S132v3.
With the s132 v3 and sdk12, I want to extend the ble transfer size.
Now I can change the att_mtu to 100, and iphone...
Hi all!
I recently ordered BLE tag with nrf51822 QFAB chips.
When I read back the memory content (with mem8 jlink command) I manage to read up to the address 24A60 which...
The task I am working on is sending a list of records from an nRF52832 chip to a central. Before sending the records, the total number of them should be sent, so the central...
Hello. I'd like to know. Can I trust to opportunite to firmware my controller (nrf52832) over the air. I mean is there any chance do not be able to do it, for example if last...
I'm using a module that has nRF24L01 mounted.
When I transmit to many PRXs, using the same frequency and channel, I expect to receive
many ACK signal at the same time.
...
I'm using nRF24L01 in a star network and i want to disable ACK.
I write the ACTIVATE command followed by 0x73, then a write to register FEATURE the value 0x01.
In this way...
I am trying to follow the tutorial given on this page:
devzone.nordicsemi.com/.../
However, my eclipse project does not build and created following log
13:55:03 ...
app_pwm_uninit is hanging the code. The control goes to pwm_dealloc() and then in nrf_drv_ppi_channel_free() it hangs.
Using SDK10. I want to change the PWM frequency and...
I am new to eclipse IDE and I am following tutorial on this page:
devzone.nordicsemi.com/.../
I am able to make the blinky project on the terminal and it does create...
Hi,
I have the following piece of code.
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<300;i++)
{
nrf_gpio_pin_clear(PIN_EN_BSTR);
__NOP();
__NOP();...
Hi,
I’m trying to use new SKD 12 secured bootloader but can’t pass signature check in dfu_req_handling.c\dfu_handle_prevalidate() (code after switch case DFU_SIGNATURE_TYPE_ECDSA_P256_SHA256...
Per table 19.4.2 in the nRF52 PS v 1.1:
, what is the difference between CL (load cap) and C0 (shunt cap)? The max ESR is specified for C0 but not CL. The xtal datasheets...
