Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
hi dear Engineers!
if I use sd_ble_gattc_primary_services_discover(..) with NULL last parameter , all SERVICES discovered OK:
start_handle=0x0001;
err_code = sd_ble_gattc_primary_services_discover...
We have a device which needs to survive dishwasher conditions. We believe most dishwashers operate up to 71C, but may reach 82C during 'sanitation' phase/drying.
This is...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. Before I add a DFU service to make it switch to bootloader, I have use...
Hello, I'm sending a series of data up to 7 bytes from an android phone, but I can only receive the first 5.
I'm asking what are the list of thing to mind if I were trying...
Hi,
I am trying to initiate Firmware Upgrade using the nRF Connect Mobile Application (also tried using nRF ToolBox).
As described in the below link -
github.com/.....
The footprint of sd_ble_gap_connect() is:
uint32_t, sd_ble_gap_connect(ble_gap_addr_t const *p_peer_addr, ble_gap_scan_params_t const *p_scan_params, ble_gap_conn_params_t...
This is what I believe, of course, my beliefs are flawed, so please DO point my errors out:
There is this attribute table on server/peripheral devices. The actual...
Hi，Nordic
I have one nRF24LU1P device, when I make it as USB Dongle, I will use :
hal_usb_endpoint_config(uint8_t ep_num, uint8_t ep_size, hal_usb_cb_endpoint_t endpoint_isr...
When I repeatedly (>290 times) send the same notification to the connected host via sd_ble_gatts_hvx, I get a sd_assertion:
Fault identifier: 0x1
Program counter: 0x104FA...
Hello,
I have a custom board which has NRF52832 SOC(i.e. main MCU) and another ARM Core-M0-based MCU(i.e. target MCU). These two are connected over I2C. I wonder how to...
nRF BLE sniffer is crashing within the first few minutes of use. Attached is the log of one sniffer
session from the start to when it crashes.
Here is my log.txt from...
I'm working my way through BLE Advertising, a beginner's tutorial and getting a SDK error 4001 when trying to use
advdata.include_appearance =
true;
Can anyone...
Hello!
I'm trying to nRF52 soc chip to drive the matrix sensors array (16x16), because there is no enough I/O pins for my project and thinking of use the shift register...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
