after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
We are using nrf51822ab, s130, pca10028. After dumping the soft device the free space left is 20kB, my code size is 48kB. I am able to dump the code into device but its not...
I am following ble_peripheral example of nrf51822 SDK 8.0. I have found ble_gatts_char_md_t , ble_gatts_attr_md_t and ble_gatts_attr_t confusing. I want to know the difference...
Hi,
I'm currently using an application that needs a very speed detection of GPIO and need to use NMI on GPIOTE.
I tryed to find how can I connect my NMI to GPIOTE but...
nrf_drv_usbd_init() calls nrf_drv_clock_hfclk_request(NULL)
however nrf_drv_usbd_uninit() calls nrf_drv_clock_lfclk_release();
Is this correct?? If so why?
Hi, I have the opportunity to bid for some research funding for my project, and I'm thinking of speccing a workstation for processing video in realtime, and sensor data in...
I am trying to add the heart_rate_meas function to the ble_app_uart project.
Is this plan possible?
However, it does not go well.
Why are you concerned with this method...
Hey Guys,
im working on some sort of application transport layer for ble and have some questions to better plan what i need and what is kind of redundant.
Is it correct...
Hello everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
I'm using nrf52 with SDK version 12.0.0. I'm trying to use the FDS for my application. I used one of the existing fds example from link fds_example .
With this example...
Hello,
I am a bit lost, after concluding the application part of my project I try to approach the ble part.
I read the "Getting started with bluetooth low energy " and...
Press down PWRON1 give rise to Q2 and Q3 conduction, the 51822mcu power on and IO send a hight level to PWRON,to keep VCC_nRF.
At this time press a lot of button will not...
Is there an unsecure version of the bootloader? I'm looking for something that will take anything as an upgrade.
I figure if I'm stuck in the bootloader anything is better...
I want to set up a rPi3 as edge router for 6LowPAN over BLE. Ideally I would like to have random devices (users) come and go by dynamically connecting to the router. Same...
