Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I have problem with one question of the lesson 5 Quizz of the "nRF Connect SDK Fundamentals" course (Dev Academy)
https://academy.nordicsemi.com/courses/nrf-connect-sdk...
I am running the examples l9_e5, l9_e5_sol and l9_e5_nrf5340_both_sol from this repository: https://github.com/NordicDeveloperAcademy/ncs-inter/tree/main/v2.9.0-v2.7.0/l9...
Hi,
i am working with the following setup:
- nrf5340
- SDK 2.6.3
- Direct Test Mode example with serial communication
I see that DTM example has changed from 2.1...
Hi Nordic team,
I'm implementing a BLE UART bridge (emulating the old SPP profile) using a custom service. The central device (dongle) I'm using only supports the classic...
Hi guys,
I am following DevAcademy lessons on nrf52833dk kit. I am testing the software on VsCode. SDK version is 2.7.0 and toolchain is 2.7.0. Board target is selected...
Hi Nordic Team,
I am working on matter-based product development using nRF54L15 and looking for machine learning support for the same SoC. Can you please confirm if machine...
How do I adjust the swd speed used by nrf connect RTT ? Currently it is 2000khz but more is needed. I need to transfer audio data to PC.
For some reason my current process...
I saw in nrf connect sdk 2.9.1 that there was nRF54L15 sample code for Channel Sounding and nRF52833 DK sample code for Direction finding.
But now I want to implement...
Hello,
I am attempting to configure the following setup to support (with an nRF5340 + nRF7002-EK)...
1. nRF7002 on SPI w/ TLS, STA, and FW patches offloaded to QSPI...
Hello,
I am using PAwR (Pe riodic Adve rtsing with Response) in coded PHY (S8) with SDK 2.7.0, following the Nordic demo :
8562.PAwR_Demo.zip
Periodic Advertising with...
Hi all,
I'm working on a BLE peripheral using Zephyr and have run into an issue when enabling both dynamic device naming and long advertising intervals.
I enabled dynamic...
Is there a way to test that the RXD and TXD pins are sending and receiving data on the nrf5340? I am trying to connect these pins to the u-blox ANT-B10-00C using male to female...
Hi guys,
we are using the nRF52833 and have a running application. Now I want to introduce unit tests and stumbled upon ztest . The idea is to add a folder where all the...
I'm using nrf52832 developing my application.
In the past I used sd_ble_opt_set() to set a static pairing code for pairing.
But now a new requirement has emerged, I need...
