Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
hi,In the host,
if(nrf_gzll_get_tx_fifo_packet_count(pipe) == 0 )
{
nrf_gzll_add_packet_to_tx_fifo(...);
}
In the devcice, every 5 min send packets to host ,but ack...
Hi,
I'd like to design a custom software an win10
to help in design a custom hardware using nrf51822...
at this time I have an eval board (PCA10028) whit a custom firmware...
We are trying to dump DFU code using Keil into nrf51822 IC. We are getting error, we are using SDK12. we tried many solutions provided in devzone, we were not able to solve...
Hello everyone,
I am trying to congifure two gpio pin (pin 6and 7) in standard high drive mode 5MA because am trying to connect those pin to the speaker inorder to increase...
When I program the board the COMP and Timers work fine. Upon removing the debugger and resetting the board it also works fine. But if I subsequently power off the board and...
Hello.
I don't know difference of GPIO's input/output direction setting.
There is two register for gpio setting.
DIRSET : Dir set register
PIN_CNF[n] : Configuration...
Hi there,
Is it possible to call SOC library functions before calling sd_softdevice_enable()?
In particular, i want to set up my interrupts with sd_nvic_SetPriority...
We want to use 52832 to control 6 LEDs. it is easy to use 6 IO pins to make them on and off. but we need these LED to blink. so we want to use one PWM module to generate 1...
When using the nrf_drv for spi master there are no problems when compiling. If I switch the SPI configurations to operate as a spi slave the compiler spits out "non-trivial...
Hi All,
I have just started working on interfacing SD card with nrf52 using SDK 12.0. I have to write to SD card at a rate of 84 packets per second and each packet consists...
Hi
I am checking out NRF51822, NRF24LU and NRF24LE1.
Below are my design requirements:
Smaller the size, the better. 7x7mm is OK. prefer smaller.
Lower power...
Hi, Nordic
I have 3 nRF52 devicies, one as Gzll Host, two as Gzll Device.
they use Gzp to pair, when paired, two Gzll Device send payload via different pipe ( 2, 3)...
Hey everyone, I'm trying to use lmt70 with nrf51822. So, first of all, nrf51 has 10-bits ADC, the data sheet of lmt70 is recommended 12-bits of ADC.
I plugged the sensor...
I use nRF51822 (Multiprotocol Bluetooth low energy/2.4 GHz RF System on Chip).To transmit informations with smartphone.
I have to set up a self-certification application...
Dear Nordic.
Is NRF_POWER->GPREGRET register writing in NVMC?
FICR and UICR is saved in flash memory(NVMC) as written by [nRF51_RM_v3.0.pdf].
But, GPREGRET register...
