Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello,
I use SDK 13 on nRF52832 with a SD card (nRF port of fatfs lib).
I have a long sleep and i want to minimise current.
With SD card, it's okay i switch off SD...
Originally, this was a complaint about SIGTRAP 0xffffffe while using GDB.
But I've discovered the actual issue is related to a lack of erase/programming of FLASH.
My environment...
I would like to know how long is the minimum pulse width for SENSE to trigger GPIOTE Interrupt from external pins on NRF52832,I have seen
devzone.nordicsemi.com/.../
How...
Hi,
What is the status of a MISO pin of an SPI instance after issuing NRF_GPIO->IN? Does it reflect the real state of the pin? If no, what fast options do I have to read...
hello ,
i have a question, when i download the application.the power dissipation is more than 1mA, and i press the reset key to let the reset pin low level,but it is not...
I have an application that first reads ADC sensor data from a SPI device, then transmits out through BLE. I have a 4ms timer; once it times out
Read sensor data through...
Hello,
I would like to ask your help for examples of nRF52 code, when entering and exiting critical regions (disabling interrupts without switching off a bluetooth connection...
Hey,
just wondering if its possible to lower the pwm driver clock of the nRF52832 to around 500Hz? Im working on a LED dimming application and the LED spots i use have...
Hi,
I got a error fatal awhile after the app switched to low advertising.
Could you please tell me where I can to look into ?
I got the error code 8198 from sd_power_systemoff...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
I found it really difficult to write DMP driver for nRF51.
I've already downloaded motion_driver_6...
Hi,
I have been modifying the MQTT Publish example for a product and found that the PUBACK message does not produce an event. The problem is in components/iot/mqtt/mqtt_transport...
I am trying to start development on the nRF52 Dev board PCA10040. However after updating to the latest nRFgo Studio 1.21.2, I cannot seem to program the board. I'm simply...
Im doing a porject using nRF51 DK,nRF51822 Bluetooth Smart Beacon Kit and nRF51 Dongle, with Termite 3,2 to view data. There's a few questions i want to ask.
My program...
