Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
We were doing various tests using PCA10040.
Then suddenly I can not connect to the PCA10040 board.
In the boot loader mode of PCA10040 board, connection is made.
What is...
Hi, I use the nRF52832 board (PCA10040 v1.1).
Before creating a custom PCB that uses nRF52832-QFAA, I chose
Q22FA12800025 FA-128 32 MHZ 8.0PF (load cap = 8pF)
and ...
This should not be a sudden my PCA10040.
Jlink are probably going to have failed.
It does not appear in the USB Jlink to appear as Atmel.
Is there a way to recover...
I am doing a project about nrf51822 smart beacon kit and a person has give me this link: infocenter.nordicsemi.com/index.jsp
to download the firmware and hardware files...
Hello,
I develop a BLE central device based on nRF52 (with the newest connectivity firmware and SoftDevice with API v3) and the pc-ble-driver in version 2.0.
Since my...
Hello Everyone,
I am working on nRF51 I need to save data with timestamp (current date and time).
Is there any example code is available so I can set current time and...
Hello,
Recently read about FIDO’s U2F authentication protocol for NFC and Bluetooth smart.
https://fidoalliance.org/fido-alliance-equips-u2f-for-mobile-and-wireless-applications...
hello everyone,
I am doing a project about Ibeacons. I need to make a selfmade bluetooth smart beacon (excuse me for bad English). I found a schematic circuit design of...
Hi all,
I am trying to get an Android Nexus 5X app to work with an NRF chip, and facing some problems, specifically with writing to a characteristic. Really hope to get...
Hi,
I discovered unusual behaviour in a SPI read transfer.
My transfer consists of writing one byte (peripheral register address) and receiving one byte (contents of...
SoftDevice Version s132 SDK Version
12.2 Kit NRF52832 PC10040 DK
I am trying to run the ble_app_beacon example after importing the project into Segger Embedded Studio...
Hi,
My application always stops at the end of ble_stack_init() exactly at:
return sd_nvic_EnableIRQ(SWI2_IRQn);
of the function softdevice_handler_init.
My board...
