Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED |
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
And then when I look up "BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;...
Hallo,
i'm trying to test my BLE aplication using the PTS. The profile test are mostly OK. But if i run the GAP Test (especially TC_BROB_BCST_BV_01_C) the PTS does not...
It seems that static and global data is NOT set to zero during start-up. This is supposed to happen according to the C-standard. How to do this in a proper manner, i.e. to...
Hi All,
we currently move our custom design to CE testing and already did some successful EMC pretesting.
However, our testing house asked us to prepare a firmware for...
Hi All,
BLE Nordic Stack: 0.9.7
Tiny Circuits: Ardunio + Nordic nRF8001 Board
First time post, and hoping someone has run into the same issue that I am. I am in the...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
Hi,
After I've successfully connected my smartphone via nRF Toolbox's UART-BLE Service to my nRF52 peripheral, I tried to mimic the scenario when the devices get disconnected...
Hello
I want to understand how far the firmware that is burnt on to a Hardware is protected. Is it possible to actually read the firmware from a device (if the device has...
Services Setup
I am trying to feed the "Services Data" manually to the nRF8001.
As per the data sheet page 82 (see image below): Upon transmission of 1 packet of data...
I am trying to run the ble_app_beacon example on an nrf51802 device.
The call to sd_softdevice_enable() never returns (jumps to 0xFFFFFFF9)
The fault handler is not called...
My guess is that:
Characteristics are (or at least, can be considered) subsets of services, which in turn, are (or at least, can be considered) subsets of profiles.
...
Hi, I am modify the S120 multi-link UART example code (code is available here ), and just noticed a problem that the central is only able to send the UART data to the last...
I have tried to make IAR working on monitor mode.(Follow this devzone.nordicsemi.com/.../ . )...up to today the NRF52 still will reset once I hit breakpoint on power_manage...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
