Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
How do I change the properties of the Generic Access service's "Device Name" characteristic to be Read Only, not Read and Write? I see this
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
Hi,
We are sending data every connection interval which is a stream using the API sd_ble_gattc_write. Whenever there is a dropped packet from what we understand, the Softdevice...
I used SDK11, SD332, and no change anything.
the application reset as picture.
can you test this issue and give suggest ,why app reset?
D:\work\nordic\BLE\SDK\nRF5_SDK_11...
I need a code example (e.g. Health Thermometer) that runs on the Beacon Kit. I have tried several combinations of soft devices and code examples, but I can't get it running...
Hello,
I started implementing a project with the device manager. I am using the S120 as central.
I am able to connect to 3 peripherals at the same time (also nordic nrf51822...
Hi,
The environment is Ubuntu 16.04 running on parallels on a mac pro.
I am following all the installation instructions and I get no errors, except that the opus driver...
Hi,
Today, i try to use the UART SERVICE from nordic on both smartphone and NRF51.
I succeed to send data between the two.
But now, i want to send data longer than 20...
Hi,
Using SDK12.1 with nrf52. Have SD and bootloader on the device and trying to load application via BLE DFU.
It randomly gets stuck. (see attached screenshot)
And...
Hello,
I have some trouble to use the Secure Bootloader example, which comes with the
nRF5_SDK_12.1.0
I installed the latest nrfutil and hexmerge. I can compile the...
This piece of code appears in all IoT SDK examples:
eui48_t ipv6_medium_eui48;
err_code = ipv6_medium_eui48_get(m_ipv6_medium.ipv6_medium_instance_id,
&ipv6_medium_eui48...
Hi, I am using the nrf uart app to communicate with a smart phone and the NRF52. I am trying to detect whenever it is sent a value between 0 and 60 from the phone, and save...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
Hello, I want to clear things up a bit, all these concepts are starting to overwhelm me somehow. I want to know:
What can have UUID and handle? I understand that profiles...
