Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I'm developing to nrf51822 mcu, using a s130 softdevice.
I'm using a BLE example code.
I get an interesting problem - when the mcu receives 2 reports (that are...
Hi,
we are thinking about using the NRF52 with the BLE SoftDevice in a security relevant application. As the SoftDevice is not available as source code, no reasonable security...
Hi all!
I want to check work of AES encryption.
Some code on 51822:
uint8_t aesKey[]= {0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39,0x30,0x31,0x32,0x33,0x34,0x35,0x36...
Hi All,
I have a problem with the function sd_ble_gatts_hvx().
I have no return value when i call this function and i don't understand why ?
I have a function where...
I am running SES 3.10f on Linux. I have followed the Tutorials regarding Monitor Mode Debugging. I don't ever get the pop up box regarding the Monitor Mode debugging license...
Hi All,
My question is about available sleep modes in nRF51822.
As I can find in nRF51 Series Reference Manual, and Product Specification documents, nRF51822 chip has...
Description:
I am developing iOS app which will connect BLE and keep the connection till user don't want to disconnect. i.e we want to autoconnect BLE when BLE is in range...
Using Master Control Panel (MCP) with nRF51 Dongle PCA10000 v1.0
Segger is offering a J-Link firmware update - v6.10l:
Is this compatible with MCP? Is it safe to...
I am using RedBearLab Blend v1.0. I ran the HID_template and HID_keyboard_template. I can see the device in Win10 advertised as joystick and keyboard. Then I tried to modified...
Hello , i am going to use nrf51822 development kit ,but i am totally new for using it, i want to know that if i have development board and i want to see result but i dnt have...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
In the MQTT-Example connection to the broker is established only when I press the button (callback), but...
Hi all,
I am facing issues when initializing and enabling the Softdevice after using the nrf_nvmc driver to erase and write flash pages. The project shall have the ability...
I am working with a MacBook Pro (El capitan) and the nRF51822 beacon and I need to measure the RSSI. I understand that the app nRF connect can do it, but the antenna on my...
Scenario is as follows:
NRF52 (SDK12.1, SD3.0) works in central and peripheral mode.
What happens is that on start we create a single shot timer with 4.2second to wait...
I write a function, It can read ok without BLE starting.
When I start the BLE , the function can not run.
So I think that , if I can use some function to stop the stop the...
