Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I want to set the reset bit to 1 in the reset register of Power Management module.
Chip used in nrf51822.
I have been trying to set the bit using the following statement...
how to send hex by nrftoolbox APP uart?
I use this app, when I start use it, I just only can send char, I can't send hex to the device. how to set it char to hex? please...
I am using the Nordic nRF51 SDK on a BLE Nano device. The example I am using uses a function to initialize the LED flashing (bsp_init()). This sets the timing for the ticks...
Hi all,
I want to use nRF51822 (s110) to measure the frequency (0 to 5kHz) of a signal connected to an analog input. Other posts ( like this ) show that a good way to implement...
Hi,
SDK:8.1.0
Chip:nrf51822
Power Mode:LDO
Battery:CR2450
Application:beacon
The equipment static power consumption is 3.3 ua, after a period of time is 1.9 ma,but...
I'm using Keil5 to compile example of SDK v12.2. And I'm trying to understand each of Source code to understand how each of it is consists of.
I opened an example "SDK...
My code hit weak handler when I try to modify the examples/peripheral/saadc to run with softdevice s140 on nrf82840 PDK. All I did was adding a BLE Stack initialization before...
On the nRF52832, what is the longest period of time that the softdevice will control the CPU while doing things with Bluetooth? This is effectively the interrupt latency time...
I am working on nRF51 and nRF52 series SoC.
I need to check whether my radio device is connected or not and also to test radio functionality(like radio range, sensitivity...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Is it the only way to call a function on a read characteristic to make a read request and then inside on_ble_event call the function?
Is this the right way?
Hi
in the communication with an SPI peripheral device, a communication cycle might take up to 5 ms.
It is implemented as a blocking function, meaning that app_sched_execute...
Hi all! Several weeks I've tryed to implement code for my wireless temperature sensor based on nrf24le1 and ds18b20. In datasheet said that in memory retention mode the power...
Hi,
Is it possible to send a advertisements for a single (or a fixed number of) Advertising Events? I need to control the number of Advertising Events "sent" for a mesh...
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol...
