Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am trying to build a BLE central application on the mbed compiler (target BLE Nano).
I have chosen the ble_app_uart_c example from the nRF5 SDK as a starting point. My...
Hi Support Team,
one error come out when use nrf connect, just as attached picture shows,
please help to check what cause this error,
no error come out on phone.
...
In reference to this issue in the Android DFU library...
github.com/.../33
... can someone from Nordic please explain how DFU OTA using the secure format on a device...
Hi,
I working on nRF52 series development boards communication. I am using ESB library for data transfer. I am able to transfer the data between two microcontrollers. Now...
My device is connected with GSM module, when GSM module communication fail, I need to save the error message to flash. In application level, pstorage_store or pstorage_update...
Hi,
I use fstorage fun in nRF5_SDK_12.1.0_0d23e2a.
and the same code can run SDK11 but It seems different now.
So how to use fstorage fun in SDK12 and I list the different...
I was looking for something like a checklist of what to do when developing on a custom board but I couldn't find it.
I am working with Keil 5.15.
I achieved to develop...
Hello, i have a question.
Can nRF51822(s120) handle more than one connection at same time?
Let me explain: i have one server(nRF51), and two(or more) clients(nRF51 and mobile...
My Chip is a Insight SIP ISP1302.
It's based on a 51822_xxAB, 128kb Flash and 16kb RAM.
I try to use the S130 with the UART Application.
The S130 2.0.1 requiers 108kb...
Hi,
NRF_LOG_PRINTF() is working fine with peripheral examples in SDK11. but when I try to do the same in ble_peripheral examples it is not working. I have defined the following...
Hi. I have one question:
From SDK and docs, I can find how many pipes and which pipe nRF24LU1 open when it is TX.
I check function:
void hal_nrf_open_pipe(hal_nrf_address_t...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
I am trying to develop firmware for the nRF52 platform using Visual Studio, as I prefer VS over Keil. I came across the VisualGDB plugin, but it seems their BSP is...
