GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
The hardware I am using is based on nrf51822/pca10028, with s110 SoftDevice version, and the SDK version for the project is 8.1.1 Using Keil uVision 5.21.A
When opening...
Hi,
I am running the mqtt subscriber example provided in IoT SDK (nrf5_iot_sdk_3288530).
I am using raspberry pi as router, and following the infocenter tutorial .
I have...
Hi ,
This is the first time I am using nRF52 and I don't have any experience about Antenna design. Here is my question: I am using nRF52 CIAA variant and planing to use PCB...
Hi,
I need to change advertisement data while advertising. The goal is to set new data for every packet. Firstly, I was trying to put new value like this, but it didn't...
hi all:
Recently, I develop with nrf52832, the softdevice is nRF52_SDK_0.9.0_0c82e3e.
In my application, I need a big buffer, so 32K ram can not satisfied. As the errata...
Hi all, we designed a custom board using nRF51822 now we need to test these custom boards working properly are not for these I'm creating a factory test project by configuring...
Hello Nordic Semi Developers..
I design my Product prototype using NRF52832
What is the plan of Nordic to provide SDK to support NRF52832 dynamic Mesh with
[1] Over The...
Hello,
I want to read the current ticks in RTC0, and want to measure the time elapsed after some events by using ticks to milliseconds.
Basically i want to display the...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
What I want to achive:
Get the IoT-SDK 0.8.0 MQTT-Example running on nRF51 and publishing sensor data...
I am using nRF51 IoT SDK and nRF51-DK.
After setting up Raspberry Pi3, I ran icmp sample in the SDK for testing ping6.
when sending about 60k byte, we could not send the...
Hello, I used to think that handles are just a member of a stuct or perhaps a field of a packet, which is used to identify data payloads.
Now it seems that I might have...
Hi,
I have a problem with the nrF8001. I connected to STM32F4 and I use the nRF8001 SDK v1.7.
I need send several (less then 20) bytes from the device to the phone with...
Hello,
I used nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0, the ble_app_uart_c example code.
I want to add the timer, after add the following code, my system can't work....
Hi - I have been unsuccessful using Master Control Panel 3.10.0.14 on win10 to send a new application to a pca10028 with running initial application that supports DFU. What...
