Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
I used a mesh example (the example name is "mesh") for testing, and enabled low-power nodes using CONFIG_BT_MESH_LOW_POWER =y, and disabled the automatic start of low-power...
I used ncs2.9.1. I download the mesh dfu distributor and mesh dfu target examples to two devices respectively, and successfully updated the mesh node through shell commands...
Hi
We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
use "nrf5340 cpuapp" to compile project, flash statistics as follows, see blue color
[3/11] Linking C executable zephyr\zephyr_pre0.elf
[6/11] Linking C executable zephyr...
Hi, I am a beginer, it is my first time using raw MCU IC, and I don't know how should I connect my 32MHz oscillator. So I see that the nordic configuration looks like this...
Hi,
I’ve compiled and flashed the Matter light bulb example from Nordic onto the nRF5340 DK.
I'm using the nRF52840 Dongle as the OpenThread Border Router, with a Raspberry...
Hello,
I have a custom hardware around the nrf52820, and I simply can't make it to run the basic hello_world and blinky samples.
I'm compiling the samples using nrf52833dk_nrf52820...
Hi,
I've just migrated my project from NCS 2.6.1 to 2.9.0 and I'm having some problems with the UART.
I'm using the nRF52833 DK to communicate with another device and...
Hello,
I want to port blinky example to 52805.
I wrote this dts file:
I added " CONFIG_DEBUG =y" to prj.cong.
I launch debug but main function is never reached...
I discovered weird modem behavior when testing my application with a weak or undetectable signal. Mine testing was as follows:
modem connected to the network
communication...
Can the npm1300 be set up so multiple interrupts trigger the same line, and then the host can determine what the cause is?
Or does each interrupt need a 1:1 correspondence...
We are developing a device that uses BLE, 4 contacts (buttons), a piezo connected via PWM and a realtime clock (RV3028). It also stores event data on an external flash using...
My application communicates via UDP and all communication is initiated from the device. Before packet transmission, network registration status is checked (CEREG) and sendto...
I boot AOK after I do a west flash --erase. But after that, when I try "west debug," I run into this:
*** Booting nRF Connect SDK v2.9.0-2e7ce73f5faf *** *** Using Zephyr...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
