I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hello,
the FDS_VIRTUAL_PAGES is set to 3 in all examples which use the Peer Manager module. The parameter's comment says
Number of virtual flash pages to use. One...
Hello,
I am completely new and I am having NRF52 series.
I would like to know is there an ready example for android or iOS phone using Bluetooth:
Control volume...
I programmed my nrf51822 with one the hex sample files that are existed in the nordic package. toolbox app can find my beacons but cannot connect to them and with nrf connect...
Hi all
The nRF51822 product specification V3.2, chapter 8.8, specifies the times t_CSD and t_CC of the SPI slave peripheral for the low power mode and for the constant...
I've experienced some struggles programming for Taiyo Yuden's EYAGJNZXX board. According to the user manual provided its chip is nrf51822 (which supposedly works with s210...
Hello.
I have a question.
I use nrf52 & Keil.
I want to get data from sensors and send it with BLE.
Now, I found sample codes.
It uses UART and sends with BLE.
...
HI,
I want to send an "Echo" command to the nRF8001 using an ATMEGA328. Can some one suggest code for it ? How should the command be coded in a packet ?
Regards
Hey,
currently I use nrf_gpio_pins_set() and and nrf_gpio_pins_clear() from nrf_gpio.h to set and clear specific GPIO ports, respectively. If I want to change the current...
Alright, I have searched high and low and been unable to find a simple answer to this question. It must be possible for the nrf51 to launch Siri on an iPhone, I have seen...
Hi!
I'm doing an Arduino .txt file sending project using the nRF24L01+. But i'm quite a noob in this so i'd like a bit of advice.
I'm using an Arduino Uno, and I made...
Hello,
while reading some nrf5 examples, I've stumbled over a pattern in the examples, where the result code of a function is stored in variable (most of the time named err_code...
Hello Everyone,
I am porting rf receiver example code which are available in another platform.
I have used this rf module : www.amazon.in/.../B00NRQ3BIM
I am attach...
I am using app_timer to measure the time taken to execute a function. I am using ble_app_template code. As mentioned in the documentation, app_timer needs to initialize the...
I am developing an advertise only code.
There is PERIPHERAL_LINK_COUNT macro in ble_app_template that is used by the softdevice to reserve RAM for peripheral link...
I am using:
DK52
SDK 11
Softdevice S132 2.0.0
I have initialized my service as follows:
#define BLE_UUID_BASE_UUID {0x05, 0x00, 0x00, 0x00, 0x00, 0x00...
