Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
i want to use timer0, timer1 and timer2 and also RTC0, and RTC1 all Sefrate by Sefrate interrupt and so on.... so, have you any coading example?.... i m using sdk12 with eclipse...
i m using pca10028.. and sdk12 with eclipse gcc tool chain setup on windows..im run Peripheral>rtc example successfully... interrupt call every 0.125sec but now i want to...
Guys I made a wireless link using two NRF24L01+ & two MCU units.I want to toggle the reciever side LED bulb when the transmitter side switch presses.
*NRF24L01+ (Black...
Is there any guideline on how to setup and use the UARTE on nRF52 ?
what files to include in my project
how to initialise the peripheral
how to setup the DMA fifo...
Hi I'm an undergrade student in dongguk Univ. in South Korea.
I want to control the sending message and receiving message.
I use the android studio.
What do I do...
Has anyone using nRF24L01 raw (CRC turned off) mode. I try to turn off the CRC (the data sheet offers this option), then I start to miss packets. Once I turn on the CRC, I...
In ble_app_uart, the tx and rx characteristic uuid are shown below, and it supposed that the Tx characteristic enable notifications while the Rx characteristic enable write...
The hardware I am using is based on nrf51822/pca10028, with s110 SoftDevice version, and the SDK version for the project is 8.1.1 Using Keil uVision 5.21.A
When opening...
Hi,
I am running the mqtt subscriber example provided in IoT SDK (nrf5_iot_sdk_3288530).
I am using raspberry pi as router, and following the infocenter tutorial .
I have...
Hi ,
This is the first time I am using nRF52 and I don't have any experience about Antenna design. Here is my question: I am using nRF52 CIAA variant and planing to use PCB...
Hi,
I need to change advertisement data while advertising. The goal is to set new data for every packet. Firstly, I was trying to put new value like this, but it didn't...
hi all:
Recently, I develop with nrf52832, the softdevice is nRF52_SDK_0.9.0_0c82e3e.
In my application, I need a big buffer, so 32K ram can not satisfied. As the errata...
Hi all, we designed a custom board using nRF51822 now we need to test these custom boards working properly are not for these I'm creating a factory test project by configuring...
Hello Nordic Semi Developers..
I design my Product prototype using NRF52832
What is the plan of Nordic to provide SDK to support NRF52832 dynamic Mesh with
[1] Over The...
Hello,
I want to read the current ticks in RTC0, and want to measure the time elapsed after some events by using ticks to milliseconds.
Basically i want to display the...
