I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi Nordic team:
I am configuring a low power application for the nrf52833 board (custom board). This is a very low power application and I want the board to stay on sleep...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Advertiser...
I have compiled code that debugs and runs normally on the nRF52840DK. I just connected my custom PCB to the debug out connector on the DK and I have two issues that are probably...
I just flashed a new image on my device using MCUmgr. In the logs, when the device boots up, it shows the correct APP_VERSION string.
returns:
I: Firmware version: 0...
Hi, We are trying to provide example support for our RAK4631 (nRF52840 based) and an ultrasonic PDM microphone (RAK18032). We have been able to get a sample frequency of 100...
Hi, I am using nRF5340 for my unicast Audio server example where the nRF5340DK is the headset and my mobile device is the audio source. I have taken the unicast audio server...
Hi,
I just can not download nRF_DeviceFamilyPack 8.44.1 from this link developer.nordicsemi.com/.../ It comes up an error of the server. Does any body knows how to get this...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
Hi,
I'm working with the nRF54L15 SoC and running into an issue when using UARTE21 together with SMP over Bluetooth . Here's what I’ve observed:
UARTE21 works perfectly...
Hi,
I have an issue with nRF Kconfig GUI in VS Code.
My prj.conf is empty, and the _defconfig file of my board contains this:
When I open the GUI and...
I'm trying to get the USB Mass Storage sample working on the nRF52840 using SDK 2.9. I followed the official guide here: https://docs.nordicsemi.com/bundle/ncs-latest/page...
