Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello,
I'm new to the nRF51 modules and I just started with nRF51422 module.
I have Keil uVision v5.11.1.0 with MDK Pro v5.11.0.
I have installed nRF SDK - nrf51_sdk_v5_2_0_39364...
Last time I used Keil µvision4 few weeks ago everything was working fine,
Today I got first a connection problem with keil µvision4 when trying to upload some code, then...
For some reason I get the following error every time I open a project in Keil.
I am wondering if the SDK needs updated?
C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_DeviceFamilyPack...
Hello,
I bought a couple of days ago, the nrf51422 Development Kit. It comes with all the items described by Nordic on the website.
Just two questions:
My PCA10006...
Goodmorning
I have few problem with this project. I took the source file from github.com/.../nrf51-ble-app-temp and I modified the main.c to use with S110 6.0.0, nRF51...
Hi,
I am using nRF51822 with Softdevice S110 v6.0 to advertising packets and I would like to know when transmission is over to read some data from external sensors. I tried...
Hi, im implemented several services and characteristics in the nrf51822 with S110, its all working (read, write and notification), tested with an iOS app.
Now i need to implement...
Hi,everyone
I want to make out 4 channel PWM with PPI and two timers , PPI configuration like this,
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer...
Hi All,
I would like the nrf51822 sleep, wake up and then continues advertising.
I try following code:
NVIC_DisableIRQ(RTC1_IRQn);
NRF_RTC1->EVTENCLR...
hello, everyone.
i am a new, i can't understand the meaning of "One event can trigger multiple tasks by using multiple channels and one task can be triggered by multiple...
Please provide me some details about how to implement watchdog functionality so that i can reset the entire system for avoiding software Hangs
I have come up with a code...
Hi,
I have downloaded the SDK 6.0 which contains the ble_app_uart and tried to compile it using GCC, but getting the following error which doesn't make any sense because...
I see the nrf51822-DK and and nrf51822-EK are now marked 'not recommended'. Why is this?
I now see an nRF51-DK and an nRF51 dongle. Are these now the current development...
Hello,
I want to use broadcaster mode for nrf51822, could you tell me please what I must to do to use this mode?
I suppose I must to set BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
