Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I want to use a timer to track time. Like having a variable that shows minutes/seconds/ms/etc.
But I don't know how to do with that.I want to use the rtc, but rtc1 had been...
Here are the commands I use to upload a program to the device:
JLinkExe -device nrf51422_xxac -if swd -speed 4000
loadbin filename.bin 0x18000
r
exit
It works...
Hi, I'm planning to made a custom PCB using nRF51822-QFAA or QFAC revision 3.
My developing environments are J-Link, IAR EWARM 7.1, SoftDevice 7.1, and SDK 7.2.
I kept...
Dear developers,
Currently, I'm developing a new application that uses Nordic Uart Service (NUS) over BLE.
Everything is working fine. However, I would like reset (delete...
Hi,
I've loaded SD 8.0.0 on the device, but when I try to load application via NRF Studio it always fails.
Im using SDK 10.
Memory settings in Keil:
IROM: 0x18000 0x28000...
I use s110 v8.00, now i need finish the dual bank ble DFU program.
who can offer a example?
the s110 v8.00 is use nrf51422,and used the ram2,
I compile the project,find...
I would like to be able to manually disconnect from a device and then begin advertising.
However, I have discovered that on disconnect, ble_advertising_on_ble_evt handler...
I have an application using N5150 SOC with S210 softdevice and using softdevice_handler, SDK 10.0.0.0, and I'm using Ant-FS to gather data from this device. I only want to...
ble_app_beacon.rar hello there i used ble_app_beacon example. i want to make some modifications. i want to put it in sleep mode after some time and again wake up after some...
Hi,
I am trying to run the example ble_central_and_peripheral_experimental (SDK 9), I program the device with S130 and the hex file. The other two devices I program it with...
Hi,
What is the meaning of "NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION"?
It means use the internal RC clock source, but what is the meaning of "250_PPM_250MS_CALIBRATION...
My application uses the WDT. In my application, I use a soft reset to enter the bootloader. Because the soft reset does not reset the WDT the program will reset while in the...
Hi, current i'm writing a program in nordic nrf51822 chip and I facing the problem of region RAM overflowed with stack after adding the BLE code as shown below :
//***...
I have a RFID application in which there is a Reader and a tag. The Reader reads the tag information once the tag is in the Reader's range. The tag is an active tag.
The...
