Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi,
I'm working with a fleet of devices using the nRF52840 and NCS 2.6.0. Some of these are older devices with a bootloader that only supports RSA signatures, and I cannot...
Hi,
I am an iOS developer trying to implement the app for an nrf51822 chip-based device. I am trying to perform DFU of application type using the objective-C files from...
As title, im using nRF51822 as a ble uart.(ble_app_uart)
But it will sleep when No connect for some time.
how can i turn off the sleep mode?
I want it be a "always...
Hi, may I looked bad , but I can not find NTF52 documentation, datasheet, evaluation board schematic, pinout, price... nothing , except the file nrf52.h in which I found some...
The following SDK files have incorrect comments:
markrages@qountdown:~$ grep 'units of 0.625' -r /opt/nrf51sdk-11.0.0 | grep 300 | grep to\ 25\ ms
/opt/nrf51sdk-11.0.0...
I configured nrf to go to sleep after 5 minutes of inactivity and then wake up by external signal (by accelerometer interrupt if any movement detected). what struck me is...
Hi again,
I'm here with another HID problem. When I flash my chip with standard HID mouse example, OS discovers it with it's declared in code name, connects succesfully...
I have designed an custom application board based on nRF51822 SoC,
Now i wanted to do testing on RF front.
I found one Test guideline(RF_Performance_Test_Guidelines_v1_0...
Hello Everyone,
I am able to do this functionality by using NRF5DK
Using Android APP (MCP master control panel) am able to make beep sound in the NRF51DK by using...
Im working with a nRF51422 EK. So, there is an android application with 2 buttons. Each of them can Set a LED. It will be set as long as the button is pressed on the application...
SDK:10.0.0
Here is the error when I compile
..............\components\softdevice\common\softdevice_handler\softdevice_handler.h(40): error: #5: cannot open source input...
Hello,
I have a project which is currently using S110 SoftDevice v7.1.0 with nRF51 SDK v6.1.0. The hardware is nRF51822 xxAA revision 2. It will probably be upgraded eventually...
Hi,
I intend to use ANT protocol for an application of soccer players trackers.
Each soccer player would wear One master and remote sensors communicating with ANT.
But...
Is there a way to know if we are in critical region?
ie: between sd_nvic_critical_region_enter(&foo) and sd_nvic_critical_region_exit(0) without explicitly using a global...
Hello,
I'm using nRF8001 with Arduino for our project. I use BLEeripheral. h and I need to know if it's possible
with the visibility of NRF
when invisible can nrf...
