Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Now, we are checking nRF51822 ADC sample program in SDK.
When P0.1 input is lower than 0.7V, outputs is 0.
We are wondering if the performance is correct.
Could you...
I've been going back and forth with my manager, and I need source to show whether I'm right or wrong about a specific possible functionality of the nRF51.
I was wondering...
Hi, I have a Nordic nRF52 Development Kit. The ADC examples work, the LED examples work, and the NFC examples work. However, none of the Bluetooth examples work. The LEDs...
My DevKit arrived today. Very nice.
Plugged it into my mac, immediately recognized as USB device. Flashing LED, mounted as storage device, etc.
Tried to enter Bootloader...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello everyone
I am trying to configure the write values like in the link loss profile it is possible to write no alert, mild alert, high alert, similarly i have created...
Hello!
I would like to know if it is possible to send an unique Gatt message that contains notification enable for multiple characteristics.
For example,
buf[0] ...
Hi Nordic,
I posted the issue with BSP package in devzone.nordicsemi.com/.../
unable to attach the main.c file mainOriginal.c
HI Aryan,
Thanks for your reply. Its working...
main.c HI Nordic,
I don't want bsp.c in my project. So I removed the bsp.c and included custom_board as mentioned in devzone.nordicsemi.com/.../
I am also using UART for...
I have the nRF52 dev board "PCA10040".
I downloaded "nRF52_SDK_0.9.1_3639cc9" SDK.
I noticed that there is no installer for the SDK.
I unzipped the SDK and using Keil...
Hi all,
Since I will use broadcast way in RF transactions between one NRF24LE1 based senders and serveral NRF24LE1 based receivers . I was told not to use "Auto ACK" in broadcast...