hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I bought a EV board below to develop in the nRF51822
( www.wvshare.com/.../BLE400.htm)
I have installed all necessary tools like Keil MDK-ARM, J-Link, nRF51 SDK and nRFgo...
Hello Everyone ,
I am using ble stack S110 , BATTERY SERVICE , my CUSTOM SERVICE and pstorage module in my application and using SDK 7.0.0 and keil 5.12 IDE .whenever a server...
Hi
We are making a product based on nRF51822 and have used the ST BAL-NRF01D3 balun, but due to lack of updated datasheets for the balun we are unable to determine if it...
my dk board : nrf51422 and nrf 52382,
the central role : nrf51422, and the peripheral role is 52382.
my sdk version : 52422 is 10.0.0 and 0.9.2 for 52382
the project...
Hello,
I would like to make an iOS app read BLE advertising packets (sent by nRF51) in background mode. The nRF51 sends ADV_SCAN_IND packets and is not connectable.
...
Hello,
I am trying to make battery service in my application so i refer the proximity example in SDK 9 and i flashed into my kit it showing always 100percent in the nordic...
Hello,
I have searched through the questions regarding RF PA recommendations but I think none solved my issue.
I would like the nRF51822 to broadcast at +10dBm, so I...
Hello to all,
i'm new to nRF51822 ble developing but have experience with embedded design on various microcontroller;
I have a little problem inside bootloader code: in...
Dear Nordic Support Team,
In previous SDK (6-7) I used to always call softdevice functions when possible/existing to keep compatibility with BLE.
For exemple, PPI functions...
Hi,all.i want to use nrf51822 to drive brushless DC motor and need use 6 pwm signals.Can i generate these signals with nrf51822? Thanks for your reply!
When calling sd_ble_uuid_encode() I get NRF_ERROR_INVALID_PARAM in one project while in another I get NRF_SUCCESS with the same params on same SoftDevice(S110 8.0.0) on same...
Hi,
Can a peripheral choose among multiple central?
Consider a situation where I have a 3 centrals.
Lets say CentralA, CentralB and CentralC with,
CentralA - High...
I am really puzzled by this and although I've read all the relevant answers in the Q/A I'm still unable to do the following:
do non-selective scanning with central device...
i can not re-download application by keil4
i download softdevice and the application to Equipment by nrf51422 then it can works
but when i disconnect usb line and connect...
i want to use codeblocks to compile and download program to nrf51422
so i try to compile example in keil/ARM by codeblocks
then it always show up error
like this
" C:...
