Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I can't afford nRFgo Starter kit as of now; so my question is if there any other way to program my application (firmware) in nRF8001? I am looking from following options:...
Hi,
File "nrf_drv_config.h" defines both TIMER1_CONFIG_BIT_WIDTH and TIMER2_CONFIG_BIT_WIDTH as "TIMER_BITMODE_BITMODE_16Bit", can these timers be configured as 24 bit...
HI,ALL,
I want to take use of hardware flow control, but when i set or clear the RTS signal, it failed.
something about the attempt as following:
the purpose:enable the...
Dear all,
I'm using an nrf51822 (running softdevice 6.0.0) with the proximity profile.
With iOS8, I was able to find & pair my device with the nRFproximity app.
After...
Hello from Spain!
It is my first time that I use a Bluetooth chip so I am following all your code stack and some answers of this portal, but I am having problems with the...
Hello everybody,
I am using RTC1 for time measurement, this works fine as long as no BLE communication is running.
The RTC is initialized with
const nrf_drv_rtc_t...
situation:
We are developing an nRF51 application with OTA DFU. we use SDK 9.0.0 and the DFU bootloader version is v8. We have prepared different two packages. Single OTA...
phenomenon:
the program is polling in the 'uart_event_handle'
my attempt:
i found that the 'uart_event_handle' is called by the 'uart_event_handler' , so the program...
I would like to know how can I use nrf52832 preview kit for audio application, i.e. I would like to use PDM interface of nrf52832, please guide me on how can i do that.
I used the app_template and built it with CrossWorks (nRF51 SDK 10)
However, the call
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION, NULL);...
Up to now I´m unable to do a reliable simple communication from a PTX to a PRX, just scatered messages arriving.
So, I´m asking a very basic working example source code...
For a sensor design I want to use timers with the UART service. I got it somehow working for the S110 version 7. The only problem I have with version 7 is that I can't use...
Hi,
This is probably a silly question, but just to be sure...
I know that when designing a PCB with the nRF51 it is necessary to keep an area beneath/around the antenna...