Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
hi,
i'm working on change 'example project file using softdevice s110' to 'using s130'.
but, i don't know where exactly need to change.
just downloading softdevice s130...
I need to use the 8.0.0 version of S110 with my beacon which contains 7.1.
Since the Android DFU utility supports updating the Bootloader and softdevice with a zip distribution...
hi,guys
For testing the comunication between BLE+timeslot device and radio device, I change the code as below:
void start_timer(void)
{
NRF_TIMER0->TASKS_STOP = 1;...
Dear Nordic,
Whats wrong with the below code. It works well in RFduino but when I try to port the same code in Keil environment.Its not working throwing error as
1.identifier...
I just got a new target board back from fab/assembly and I'm trying to use the debug out connector on the PCA10028 to program the new target.
My target is the NRF51822...
Is there a beginners guide on how to get a console output working for the following setup?
keil v5 & SDK 6.1
nrf51-dk connected with the
TC2030-MCP-NL to a
nrf51822...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I am new to working with nrf52 and was looking for a way to make printf work in a blank project that I have created. I followed the uart example for the peripheral...
Hi
Now I'm using the pstorage module to save some data.But I meet some problem,I hope I can get your help,thanks a lot.
It seems that the block has been created successfully...
Hello everyone
i am trying to run the pwm library exmaple from github into the SDK VERSION 9.0 but it is showing lot of errors like
............\components\drivers_nrf...
Hello,
I am working on S110 SDK 9.0 and softdevice 8.0 on EK board. I am able to authenticate the connection using static passkey.
I need the information about encrypting...
A LOT of great information is presented by the engineers. Is it possible to post videos of the presentations?
Apple does this for the WWDC sessions. I find myself watching...
Hello Everyone,
i ahve been working on NRF51 series for past two months but suddenly i came to know about NRF52 series the apckage is ame and proce also not varying much...
Hello,
Now I am using nrf51822 with PCA10004 EK board. And the custom board we are using is BL600-SA module. As BL600 can be used with nrf SDK and softdevice, Can I use...
