Hey guys,
I use SDK 3.0.2 and toolchain 3.0.2 and want to start with the modem shell example: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/modem_shell...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
L.S.
Today I decided to have a look at SDK5.1.0 for nRF51822 which supports the S120.
It is deliverd as an msi file with (as far as I have noticed) no support for specifying...
Is there anything preventing anyone from uploading the tinyest image that simply dumps the entire ROM content on the UART?
This would sort of circumvent the HW locking...
Hello,
I use nRF51822 for my project and I would like to purchase some BLE packet sniffer. Does anyone recommend any sniffer? My purpose for that is debugging and check transaction...
On PCB layouts I often see that the HF xtal is oriented at 45 degrees relative to the orientation of the 51x chip (that is to say the edges of the the xtal and 51x chips are...
Hello Nordic expert,
Regarding the antenna load impedance, I can find the data in nRF24L01+ datasheet and it is 15ohm +j88ohm.
But I can not find the antenna load impedance...
hi,
now ,i have save the power,so need to close the spi interface at some time.
but when i call follow function (hal_spi_disable).
it see not close the spi interface, ...
Hello,
During programming bootloader provided with sdk
I get some messages in Command window in Keil.
Load "C:\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\device_firmware_updates...
Since I'm writing code for my own board, I decided to create my own board.h file to hold the board-specific definitions.
However, I can't do this without hacking the SDK...
Hi,
We have two services, apple ANCS and Alert Notification on iOS. We try to connect it with 51822. There is an exception case the the alert notification function not...
Hi,
Sorry, it looks like a ios question. We found that when connected ~10 or more 51822 devices, the iOS BLE will malfunction. We can no longer connect new device to the...
Hello,
I'm using the nRF8001, and I'm trying to max out the bandwidth between itself and an iPhone. The iPhone's connection interval is 30ms (minimum). I'm sending 20 bytes...
As title, does nRF24LU1+ have updated version(16 bit or 32 bit MCU )?
We need to process audio signal in conjunction with nRF51822(device side), but the current nRF24LU1...
I got a question to upgrade firmware in keil and after that I can´t program the device and in nRFStudio I tryed recovery but it does not work. In "keil/Config flash tool"...
