I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I'm going to configure nRF51822 chip as a spi slave.
And there are no more pins for the connector.
So I am trying to connect SS pin to the ground pin, instead to connect...
Hello
I'd like to write my own application for flashing nrf51822. It will add some additional information info hex file.
How can I burn hex file into the flash using...
Hi,
I was wondering if you can please clarify the licensing terms for the nrf51 softdevices?
I found the link to the SDK license here:
devzone.nordicsemi.com/.../license...
Hi,
I am trying to use GCC with Eclipse as explained in this tutorial , and after spending hours trying to figure it out, I am completely lost and ask for advices and help...
Hello,
It appears that changes were made to the DFU bootloader project in SD 8.1. The project no longer seems to function when using GCC.
I am using GCC 4.9.3
when...
I'm following these instructions. And downloading a project from this github repository.
The downloaded github zip file contains the following folder "ble_app_uart_c_S120...
Hello,
I use this program.I take values.Android Application want to show the values.
Program:
#include "ADXL345.h"
ADXL345 accelerometer(p5, p6, p7, p8);
Serial pc...
Hi all,
I would like to use the Arduino programming environment on my nRF51422 prototype. I have seen that RedBearLab has done the migration for the nRF51822 which quite...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
I have a fully working project that uses the HomeKit SDK 1.0.0 from Nordic Semiconductor.
In order to be compliant with Apple specs I am trying to upgrade to version 2.0...
