Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi ,
I am using 2450bm14e0003 this instead of LNA circuit provided by NRF24L01P-R7 .Is it better to use this balun Ic or i should use the circuit provided by nordiac only...
I want to make a Bluetooth connection with nrf51422.
I am using the Keil software.
But I do not understand what the program will do the bluetooth connection.
Can you help...
I am running the Blinky code provided in nRF52 SDK examples.I am not able fix this error pointing at nrf_delay_ms. This function is hard to explain. Moreover I don't know...
To test one functionality, I am sending 1Kbyte of data to smartphone using nRF51 Uart example code.
I have tried testing with different baudrates, 9600, 115200, 38400,...
Hello,
I have an existing microprocessor application that I want to test with the nrf51822. I am currently using a different BLE chip. I do not want the trouble of porting...
I'm having a strange problem. I'm running the nRF51-DK with a dual-bank bootloader, S110 soft device, and my app under gcc. I'm using Eclipse Luna as my develpoment/debug...
When i added timer in my bluetooth code my board will not advertise.using pca10028 and nrftool box uart app on iphone 5s.
here is my complete code. Using timer1
Final with...
I'm using the 0.9.2 SDK SPI slave example to connect to a SPI master (Atmel SAM4S). When I initiate a SPI transfer from the master side I can see that all the data arrives...
Hello,
I have been going through devzone questions to figure out how to enable the default debugging messages through Putty for the ble_app_proximity example project from...
Hi:
I make the gazell ready, and I need an extern PA(RFX2401) for a long distance commuicate. But there is some trouble when enalbe the PA.
My function:
Host:
pin_Set...
Hello,
I am using ble_app_multilink_central example as a foundation of my app involving central - peripherial connection (S120 - S110). My app works nicely but i have problem...
Hello, I am trying to establish a connection between the nRF52 board and the USB serial converter TTL-232R-3v3.
The setup is such that I connect the converter cable to...
Hi all,
we have a project based on nRF51422, SDK 6.1, Softdevice S310 2.0.1.
We use the bootloader for DFU services. Our problem is to send a service changed notification...
Dear all, I had debugged example Heart Rate Service from SDK 9.0.0 without problems but I think we have a exception, when I insert a breakpoint on line 923 instruction APP_ERROR_CHECK...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
