Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hey All,
Just trying to get some advice/examples on how to incorporate notifications into a Custom Service on a nrf51 Dk board using gatts. I have found a couple of examples...
Hallo everyone. I'm working with the processor nRF51422 with S210 softdevice and I would like to ask you if it's possible to drive results of LPCOMP to a General-purpose I...
My goal to build a device that can connect to phone with nRF8001.
I am using nRf8001 Development kit. My prototype uses TI msp430 with the nRF270 board in the kit, and I...
Hello,
I am using a Windows 7 VM (VirtualBox). I can flash my NRF51 DK using nRF Go Studio just fine.
When I open the Master Control Panel (3.10.0.14), I can see the device...
Where can I find a description of the different nRF24 part numbers? Specifically, I am interested in learning which part numbers correspond to OTP variants. Thanks!
Hi guys, I have an application, where I need to change the role of the S120 softdevice on demand. So, the application boots into central role, reads a couple of BLE sensors...
I am using a photo detector to sense heart beat data. That sensor data is being sent to my nRF51 DK's ADC and then transmitted out via Bluetooth. I want to collect that data...
I'm using nrf51-ble-driver_win_0.4.1 to connect BLE devices on PC. When device has a 128bits UUID, you have to call sd_ble_uuid_vs_add( &uuid128, &p_type ) to register the...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
i tested coap-server example. it works well.
i will test mqtt-subscriber example.
my question is...
Sometimes the service discovery procedure in Android will discover all services but not the characteristics included in them. So all services will be empty. If I then open...
The nRF51 SDK (version 9) documentation tells to activate SPI using the SPI_MASTER_0_ENABLE and SPI_MASTER_1_ENABLE macros. Where should these definitions be made? Other components...
Dear all, after solution of some compilation errors on github nrf51_ble_app_lbs_master for SDK 8.0.0, I tried flash application using nRFgo Studio, it says that application...
Hi,
I am using the sample ble glucose code provided in the SDK.
When i am trying to connect it over BLE interface through Master COntrol Panel or iPhone app it asks for...
I haven't updated my copies of the nRF tools, or mBed's nRF51 code for some time. I just did and now it seems my old method of flashing no longer works. I was doing something...
Hi all,
I've developed a firmware solution for one of my clients. I've compiled using Keil, testing it on a board which previously had SD110. Then I delivered .hex file...
