Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
I am using the nRF51422 for sensor. This sensor is paired to a slave in the most simple way: the slave searches with a wildcard for a sensor and the stores the devicenumber...
Looking for a 3rd party supplier with a certified module.
Module pinning makes it possible to program new software into the module.
The question is: If I change the software...
Hello,
I am using nrf51822 with softdevice 110.
I have noticed that there is some power usage between advertisements, that is more than what is being used when no advertising...
We're having difficulty preventing our nRF51822 from resetting when ESD events occur. These events are not directly on the nRF51's I/O pins, and we've tried things like grounding...
Hi,
I am having a BLE peripheral on NRF51822 chip.
I have set to MITM to 0.
I want to communicate with an iOS app which will act as central device.
When i first connect...
Hi,
I'm planning to use the nrF51822 in the end product and the nRF51DK kit has nRF51422 and not the nRF51822. the user guide for the kit says that 51422 supports ANT protocol...
I am doing a bootloader to support updates via ESB. I am using MicroLib. I am not using SoftDevice.
My project mapping:
Bootloader 0x0000-0xBFF
Application Vector Table...
I use Keil uVision 4.74.0.22 to compile nRF51-ble-bcast-mesh-master with nrf51_sdk_v6_1_0_b2ec2e6 and get the rbc_mesh_BLE_Gateway.hex. However, I drag and drop the hex file...
The iOS app we have is identifying the device via the name broadcasted and the service UUID. On production devices, are the Service UUIDs on the same product, the same on...
Fisrt of all, I have searched all the questions but now still can't make bond work.
I've done below work:
1, modify main.c file to add device manger function
2, modify...
Hello,
I am using NUS service as a peripheral with read and write characteristics and tested on master control panel.
Now I am using S120 stack for central device and...
Hi,
I have a PCA10028 which has a 51422, and trying to run ble_app_uart_c example on it. But no success. I don't get any thing on COM and LEDs do not turn on at all. Does...
Good morning,
I am using nRF51 SDK v10.0.0 and I have to synchronize access to a hardware resource shared between two control flows. One flow is an interrupt handler invoked...
I just ported my SDK 9.0 app timer code to SDK 10.0 which requires the use of the new APP_TIMER_DEF() macro. The problem is that is generates warnings in Keil (v5.17) that...
I am using nRF51822. I want to know that how to perform file read, delete and write operations. Is there any API available for this. If file operations are not supported by...
