Hello,
I am trying to factory reset 2 nrf52840 dongles that I had very long ago with unknow applications on the dongles. When I erased and installed the image of nrf_desktop...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hi,
My Nordic kit just stopped detecting from last two days.
I have also check this in other PC also.
It detects some times some times not.
I am using Windows 8.
I...
Hi all,
I would like to know if it is possible to use the uart before the actual bootloader runs... I need to communicate with the master uploading the firmware before...
Hi All,
I need to implement a kinda a mesh network of Nordic device nodes placed nearby to act as a relay, for that I have a use case where following requirement.
...
I'm porting a nrf51 project to nrf52. I'm using softdevice s132 1.0.0.3 alpha. When compiling I get a lot of L6406E errors and a L6407E error. Do you know what's causing this...
hi,
I should how to transplant the official DMP mpu6050 library to nrf51822 above?I don't know how to transplant it and could you tell me how to transplant it?
I have combined to programs Ble_uart and Spi_Master into one. However, after uploading the file the GPIOs do not work (No clock is generated). Meanwhile when I erase the softdevice...
hi,
I downloaded the master control panel(mastercontrolpanel.3.4.0.8098.x64) from Nordic website, but it can't install it in my PC becuse of my 32 bit windows XP system ...
Hi,
Here is the piece of code that is bugging me.
The code algo is at every 500ms timer2 interrupts, and the adc captures 1500 samples and stores it in an array .I always...
I'm using nRF 51822 to develop a proprietary wireless protocol.
At Rx side, every 500ms have a listening window with 10ms to listen if there is package to receive. So 10ms...
I am testing with SDK6.1 S110 7.1. I've noticed that when I try and update the Bootloader image using the Android MCP app, everything updates fine. I have logic in place that...
Hello fellow developers,
I am new to BLE applications and I am trying to do a very simple device with three buttons that informs a Android smartphone when one has been...
Hello all,
I have an ANT project which is running fine using S210 SoftDevice (SDK v8.1.0).
Now, I am trying to extend this project for BLE operation, by switching the...
I have my devices programmed in a way, that they decide whether to enable SD and transmit via BLE or to keep it disabled and start operating using Gazell.
In this case I...
So Segger recently asked me to update my Driver to V500j to be able to run my new J-Link programmers. However this update has completely bricked my Test Software which uses...
