I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I connected my SEEED Ble Micro module via SWD to my nRF51-DK.
I then pressed ERASE ALL in the nRFgo Studio.
It worked. Now my Module is kinda empty. How to get stuff...
Following the instructions from the bluetooth sniffer guide, the sniffer code finds my device. I then attempt to launch wireshark (which has been installed) and I get a plugins...
I'm trying to download a HEX file to an nRF51822 using Keil and ULINK PRO. The hex file was generated by the mbed compiler and works if I drag and drop it using the programmer...
Hello devzone...
My setup: nRF51422 and S110 peripheral
My setup transmits IR data on reception of Bluetooth data from a central device. I have used PWM for generating IR...
I bought 5 Seeed Micro Ble Modules. On their Website they answered a question 7months ago, that they ship with QFAA G0. I connected them via SWD with my nRF51-DK.
God damn...
I am trying to decrypt some data.
My data is encrypted using AES-ECB No padding method.
I know the 32Byte key used for decryption.
Following is the code snippet. I am not...
I guess and hope not but I am a little confused by the compatibility matrix..
I would need to use SDK 7 or higher for my nRF51-DK
but I would need to use SDK6.1 or lower...
Hi,
I searched here for a while and I couldn't find the answer. I implemented custom service by referencing nAN-36 and the github code. For some reasons, the github code...
Hi there,
I am trying to generate a pulse on a pin using RTC1 and PPI. Using a TIMER this works fine but my goal is to incur minimum current consumption by using only the...
I was trying to calculate analog voltage in nrf51822 through ADC.
I used analog 2 pin
ref voltage =1.2v
pre scaler = 1/3
so while i connected 0.9v to analog pin.
I see...
In the sensor datasheet it says one can use SPI_Mode 0 or 3 (doesn't say that there is anything to do to switch between them).
I connected MISO from the DK with SDO from...
I want my application to cooperate with DFU. I am using example DFU project from SDK (6.1) (from nrf6310 folder, i simplified it so it could work on PCA10000), but i need...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
