Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
Hi Team,
I am testing UART on nRF51 DK kit.
I have flashed uart_pca10028 .
I have taken out jumpers from P0.9(TX), P0.11(RX) and GND and connected to PC com port.
...
I have the example app working nicely now, so I want to export the project to a zip or something, effectively copy it, and put it elsewhere in my filesystem and work with...
Hi,
I tried installing the kernel (raspbian-kernel-zip Raspbian kernel for Raspberry Pi 3.17.4 ) on a Raspberry Pi 2 (Model B 1 GB). I found out that the Pi doesn't boot...
I'm trying the multilink central example with s120 and SDK 7.2 (because of simple_uart).
However, my PCA10028 board gets stuck at this macro:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
My code is attached but essentially it is saying that SPI_MASTER_0 is not defined when I compile. I have the line:
#define SPI_MASTER_0_ENABLE /**< Enable SPI_MASTER_0...
I'm trying to get the ble_app_hrs working on PCA100001, the software installation is brand new (all installed today). I modified the pca100028 ble_app_hrs to try work with...
Hello everyone,
I have problems with my nRF51822. I think it is related to the starting memory address of softdevice. I attach 2 nRFgo's screenshots.
I have programmed...
Hello all,
my question is related to notifications and to maximize data bandwidth using them;
First af all i have already read this: devzone.nordicsemi.com/.../ but it is...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hi,
I just updated to nRF51_SDK_8.0.0_5fc2c3a.zip and try to compile ble_app_hrs example (with S110 and DFU) with gcc 4.9. I have couple of problems, first is that some...
Hi,
i am using ble_app_template and i added the file "ble_lbs.h" in the main file. Also added this code in the services_init method
uint32_t err_code;
ble_lbs_init_t...
