Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am altering this project: nRF51_SDK_8.0.0_5fc2c3a\examples\ble_peripheral\ble_app_hrs\pca10028
I am trying to turn on the BSP UART. I main.c the project uses...
Hello,
I am using the custom board.
There is 32MHz external oscillator.
So, I implemented like below source code for clock control.
NRF_CLOCK->LFCLKSRC = (CLOCK_HFCLKSTAT_SRC_Xtal...
Hey,
we encounter very strange behaviour when using encryption (without MITM) in conjunction with write without response . If characteristics are unencrypted (open), write...
With ShockBurst activated the PRX receives some of the packets at 7 to 8 meters, and the PTX only receives the ACK at 4 to 5 meters….
The explanation for this is that the...
I'm asking because I recently figured out my modules aren't based on revision 2 chips as expected but on revision 1.
Maybe someone already made some experiences on this...
I connected my SEEED Ble Micro module via SWD to my nRF51-DK.
I then pressed ERASE ALL in the nRFgo Studio.
It worked. Now my Module is kinda empty. How to get stuff...
Following the instructions from the bluetooth sniffer guide, the sniffer code finds my device. I then attempt to launch wireshark (which has been installed) and I get a plugins...
I'm trying to download a HEX file to an nRF51822 using Keil and ULINK PRO. The hex file was generated by the mbed compiler and works if I drag and drop it using the programmer...
Hello devzone...
My setup: nRF51422 and S110 peripheral
My setup transmits IR data on reception of Bluetooth data from a central device. I have used PWM for generating IR...
I bought 5 Seeed Micro Ble Modules. On their Website they answered a question 7months ago, that they ship with QFAA G0. I connected them via SWD with my nRF51-DK.
God damn...
I am trying to decrypt some data.
My data is encrypted using AES-ECB No padding method.
I know the 32Byte key used for decryption.
Following is the code snippet. I am not...
I guess and hope not but I am a little confused by the compatibility matrix..
I would need to use SDK 7 or higher for my nRF51-DK
but I would need to use SDK6.1 or lower...
Hi,
I searched here for a while and I couldn't find the answer. I implemented custom service by referencing nAN-36 and the github code. For some reasons, the github code...
Hi there,
I am trying to generate a pulse on a pin using RTC1 and PPI. Using a TIMER this works fine but my goal is to incur minimum current consumption by using only the...
I was trying to calculate analog voltage in nrf51822 through ADC.
I used analog 2 pin
ref voltage =1.2v
pre scaler = 1/3
so while i connected 0.9v to analog pin.
I see...
