Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I am trying to do a simple UART test with nRF51822 without BLE functionality. The code is a simplified version of the UART example in nRF51 SDK, and can be found here . It...
Hi,
I just wanted to try out the DFU on the Android app to see if I can successfully update the application on the beacon. For that, I only uploaded the precompiled nrf51822_beacon_app...
Using Blend Micro (Arduino Uno + nRF8001) to gather environmental sensor data and send to mobile via notifications. Here's my main loop:
void loop()
{
aci_loop();
...
Hello,
I know I have seen the topic on the forum, but can not find it. What changes need to be done to a example project designed for a softdevice 110 to convert it to...
The s310_nrf51422 migration document states:
Due to an issue present in this release, the application is required to set the device address to the factory default right...
Hi,
I was just wondering what the sequence of events would be in the following scenario:
A S110 peripheral device (GATT server) has a characteristic with write access...
Hi all,
I've spent 4 days now (!!) on getting a "Hello World" project to work in eclipse with GCC. I guess something around the startup-code is setup wrong in my very simple...
Hello, I'm using nRF51822-mKIT for a research.
To verify ADC readings from analog input, I've connected P0_5 to GND and ran the following code:
uint16_t adc_result;...
For my project I would like to use this bluetooth module: freqchina.en.alibaba.com/.../Fingertip_size_nRF51822_Module_Ultra_Low_Power_Bluetooth_4_0_Low_Energy_RF_Module.html...
I am trying to connect to a peripheral through s120 central and vendor has a 128 bit fixed UUID
I am trying to add it on central using sd_ble_uuid_vs_add(...,...) but it...
I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I'm able to read the characteristic's value by
BluetoothGattCharacteristic...
I'm using nRF51822 SoC and I have a LIS3DSH accelerometer connected to the ship via SPI bus . I used the SPI master example . So i used the switch_state() function then took...
Hi, I would like to know how I can immediately detect when a connection link is loss either from the central or peripheral. I need to know which error or notification to look...
Hello.
Here was the question about S120+DFU and Petter Myhre said that Nordic ready to release the new S120 version with the peripheral mode support, so making DFU OTA will...
