I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi
I am try to developing ble mesh gateway to connect and controll different nodes using nrf52840. Please give guidline to do this. I think proxy node is bridge of host...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Good day,
I tried to build the standard Nordic application: Blinky for the nrf52840dk/nrf52840 board from the following directory on my PC: c:\ncs\v2.9.1\zephyr\samples...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
in prj.conf
I have several warnings in my application that look like this XXXXXXX set more that once. Old Value "x", new value "x". I am worried that this indicates I...
I am facing the following error. I have referered light switch example and have included all the required configs in the prj_fota.conf file
CONFIG_NCS_SAMPLES_DEFAULTS ...
Hello,
I am working on a custom PCB that involves the NRF5340 and our first iteration of PCBs had soldering issues during assembly for the nRF5340. The nRF5340’s footprint...
Hello Nordic,
I am running a project, use the chipset is nRF54L15, I want to know if there is any USB dongle with software can be used to test BLE function of chip nRF54L15...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
I am using NCS 2.7.0
i am running this build command from a terminal in VSC for the nrf/samples/bluetooth/Direction_finding_connectionless_tx sample
west build -p -b nrf5340dk...
