Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
I have a project that requires full-duplex voice comms (doesn't need to be high-quality). I'm evaluating the suitability of BTLE for the task. The new nRF52 has a PDM module...
I'm moving to Nordic from "another" BLE s.o.c. where the UUIDs, profiles, services and characteristics were defined in XML. With that product I could modify or examine or...
Hi
In nRFgo Studio there is an option to read the entire memory of a chip. In my case nRF24Le1 to a .mhex file.
The first lines of the .mhex file says:
Infopage:
Identifier...
I try to create a beacon which can receive dynamic UUID through UART and advertise with the received UUID.
Now I am working on the sample ble_app_uart, to replace the existed...
Hi,I have need to set TIMER2 interrupt at high priority because I need a interrupt at 0.5ms.
This interrupt must comes while Softdevice is enable and my device(nrf51822 beacon...
I've a query regarding the assert message that I see in the application.map file, when I use GNU Toolchain for building the application firmware for NRF51 SOC.
Environment...
Hello,
We avoid MITM attacks by using a static passkey. Does it mean that the attacker can decrypt the connection if attacker get the passkey? What I transfer or receive...
Keil uV5, nRF51822, TWI hardware version
I'm trying to use twi_hw_master.c and I have made one simple change to define the CLOCK and DATA pins to 1U and 2U for my target...
From reading the product specification and the reference manual, it appears that there is no accessable DMA controller. and since there is no EASY DMA for uart, how would...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including nrf_delay.h compiling with gcc:
Nordic/nRF51_SDK_9.0...
I have another problem ,when i debug s130 demo by jtag,set free run,the software running OK
,but when i set a breakpoint or stop running,then free run again,the software...
I run a laptop which previously ran this fine on Windows 7 x64. I now run Windows 10 x64.
I cleaned out j-link, nrfgo studio, libusb etc and reinstalled nRFgo Studio again...
I know that it is possible to make 4 PWM outputs, but I need to generate 5. I will be using SoftDevice 110 and BLE. Is there any possible way to generate a 5th PWM output...