Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I seem to be getting into sleep() fine with not able to connect to my app!
but getting back to work from sleep() is taking toll and its not working simply.
I'm trying...
Nordic will release a new development kit in april, named mkit.
It is based on arm mbed .
Writing a ble app will be easy, fast and simple using mbed BLE API .
My question...
Hello,
I compiled the pc10001/blinky_example with gcc/makefile, i can flash it with nRFgo Studio and it works. But if I try to compile/flash the pc10001/button_radio_example...
My computer is running KEIL MDK4 and nRF51 SDK4.
So far no problem with nRF51422QFAAC0.
Upgrading to Keil MDK5 would be a nightmare, so that I gave up after a few days...
Hi,
I'm trying the nRF UART example but I can't get it to work.
I have opened the uart_example project in uVision and loaded it to PCA10001.
Then I opened the Master...
I want to add timer to send sensor movement data to PC every 8ms(125HZ).
But when I add app_timer like normal
1.raise APP_TIMER_MAX_TIMERS
2.raise APP_TIMER_OP_QUEUE_SIZE...
I am testing Keil MDK5 and created my own simple nRF51422 project (not from the sample), hello world type of code. But the "download" button is disabled.
The J-Link is configured...
Hi,
Can anyone please tell me the exact way to enter into the bootloader mode by writing some characteristics with specific value.
I tried setting
NRF_POWER->GPREGRET...
The existing Master Control Panel cannot be used as an automatic test platform.
Basically I am looking to send commands via a tcp/ip which will invoke scan/connect/disconnect...
I'm trying to measure a scaled down battery voltage level on an ADC pin. Given my resistor values the voltage on the pin should be about 0.279 times VBATT, to fit within 1...
Hi Nordic guys,
How much is the current consumption of the LDO only (quiescent current), without DC / DC converter, in uA? How much is dropout voltage and PSRR (ripple...
I try to modify "ble_app_ibeacon" sample code. But when I add some adv_uuids for services to advdata.uuids_complete or I changed advdata.name_type from BLE_ADVDATA_NO_NAME...
Hi,
I need to write a validation document for nRF51822 . The first step need is the specification for its calibration. But I couldn't find it in your website. Can you send...
