Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
I'm trying to download a HEX file to an nRF51822 using Keil and ULINK PRO. The hex file was generated by the mbed compiler and works if I drag and drop it using the programmer...
Hello devzone...
My setup: nRF51422 and S110 peripheral
My setup transmits IR data on reception of Bluetooth data from a central device. I have used PWM for generating IR...
I bought 5 Seeed Micro Ble Modules. On their Website they answered a question 7months ago, that they ship with QFAA G0. I connected them via SWD with my nRF51-DK.
God damn...
I am trying to decrypt some data.
My data is encrypted using AES-ECB No padding method.
I know the 32Byte key used for decryption.
Following is the code snippet. I am not...
I guess and hope not but I am a little confused by the compatibility matrix..
I would need to use SDK 7 or higher for my nRF51-DK
but I would need to use SDK6.1 or lower...
Hi,
I searched here for a while and I couldn't find the answer. I implemented custom service by referencing nAN-36 and the github code. For some reasons, the github code...
Hi there,
I am trying to generate a pulse on a pin using RTC1 and PPI. Using a TIMER this works fine but my goal is to incur minimum current consumption by using only the...
I was trying to calculate analog voltage in nrf51822 through ADC.
I used analog 2 pin
ref voltage =1.2v
pre scaler = 1/3
so while i connected 0.9v to analog pin.
I see...
In the sensor datasheet it says one can use SPI_Mode 0 or 3 (doesn't say that there is anything to do to switch between them).
I connected MISO from the DK with SDO from...
I want my application to cooperate with DFU. I am using example DFU project from SDK (6.1) (from nrf6310 folder, i simplified it so it could work on PCA10000), but i need...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
Hi
I am trying to debug the "ble_app_hrs" example from SDK 6.1.0 (using keil IDE), on 51822 chip.
The IROM1 is defined to start at 0x16000 (meant to be used with softdevice...
I'm trying to minimize current consumption on my BLE peripheral and I wanted to know what advertising data is required. I have a custom service with a 128-bit UUID but do...
