I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi all,
It is a common convention to configure the I2C SCL signal to be push-pull instead of open-collector if there are no other I2C masters in the system (saves a pull...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
I have finished developing an application, utilizing the nRF 9151 DK, and I am now working on transferring the firmware to a custom board and testing it. However, when creating...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hi! It seems that I may have uploaded a non-working application to the Thingy91x. Therefore Device is not conectable via USB. The device is responding only in "MCUBOOT" mode...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello all, I am writing this as I am very new to Studio visual code, nrf connect, and many various things used in this project. Currently I am using the two samples given...
dear all,
We are fighting with a problem that defied every effort to solve it so far, so we are asking for help. Our custom board is based on the nrf5340 SoC connected via...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...